2 in-1 Inner-Outer Pipe Deburring Tool,PVC Chamfer Tool,Chamfer Reamer,Pipe Deburring Reamer Plumbing Tool for 0.75" to 3.89" PVC,CPVC, ABS, PP, PE Pipes(OD fit 0.75" to 3.5", ID fit 0.92" to 3.89")

This deburring tool is supposed to reduce the need for additional tools its durable construction but when using it in the pipe the shavings have no where to go so it will get a little gummed up and you have to clean it out before you can go on. Overall it's great little tool to make your life a little bit easier.

great functionality and excellent value. I use this to prep pipes in my swimming pool repair business. Excellent tool to have in your tool box. I only wish you didn't need to use an allen hex key to change from internal to external chamfering. 2 in-1 Inner-Outer Pipe Deburring Tool,PVC Chamfer Tool,Chamfer Reamer,Pipe Deburring Reamer Plumbing Tool for 0.75" to 3.89" PVC,CPVC, ABS, PP, PE Pipes(OD fit 0.75" to 3.5", ID fit 0.92" to 3.89") $19.40

Doesn’t work on Plastic. Made it worse on PE

shipped dull and there is no relief area for shaving to go so after much spinning on the PVC pipe I did get a tapered end but the pvc was melted into in crack by the knife

This came just in time as I was working on drainage for a ground level deck. I have tried a deburring tool before but that one only chamfered the outside of the pipe. When I work with PVC, I also want the inside clean so that there is nothing for hairs and other things to catch on and start a clog.Pros:Sturdy and lightweight.Works on both the inside and outside of a pipe.With some grippy gloves, you can actually turn this by hand although it takes some practice to keep it level.Blades can be sharpened.It covers multiple size pipes.Cons:It does say to put 2/ 3 of the shaft on the side of the cone you’re attaching to your drill, but that means having to stop, get the allan wrench and reposition the tool shaft each time you’re switching from one side to the other.In the instructions it does say to turn clockwise while working, but looking at the blades, there is no difference between the two sides. Mine actually cut better going counterclockwise and took fewer turns. Going clockwise takes more turns and more downward pressure.There are two allan wrenches included that are different sizes. Why didn’t they just use one size?The tool shaft actually came loose while I was working with it. Be sure to tighten all allan screws before using the first time.This cuts at a 45 degree angle. When I do this by hand, I do so at maybe only 20-25 degrees. I’m just cleaning burrs and taking the edge off.I’ll have to use this a couple more times to see if I’m going to keep using it.

Decent quality. Made of aluminum,Does fit on the drill. The shank seems to be a bit rough on the edges and could cut youbut overall works fine.

Being completly honest here. I have been a plumber for over 20 years and I rarely use a reamer. I know that it is the proper way of installing the joints but it's super time consuming and adds an extra step to my system that has worked great for me for years. However I have always had the tool to do so in my truck for special occasions. What I would call special occasions is when using a neoprene gasket transition fitting for cast iron or when I have to use a fernco, clamp all, or mission band type fitting. In those situation I do like using these especially on a neoprene gasket they are hard enough as it is so I'll take all the help I can get. I'm trying to get myself in the habit of reaming copper water lines more often because it is much more important in my opinion to avoid turbulence which sounds crazy but I have seen first hand what it can do. Anyways much of a rambling review but I would say this tool is quality and fits a large assortment of pipe sizes. It fits on a standard drill which takes the manual part out and makes the task quicker and easier. For any plumber this is a tool we all need I'm replacing an old version that isn't as versatile as this tool. Nice find for the versatility of the tool and for the quality it is built with. I would recommend to any other plumbers or homeowners doing plumbing in their spare time.

I picked this up in advance for repairs on my pool valves and filter. I’m a firm believer that it’s better to have it on hand before you really need it!Good solid machined aluminum with the 3 cutter blades reminds me of an engine valve cutter.Blades are a little bit adjustable with the 3 mounting screws and the play in the holes.I will probably touch up the edge of the cutter with a whetstone to make it sharper.Overall a good deal for the price point.Large enough to be used on almost anything in your home! Should be very easy to use!