10x2.125 Scooter Tire, 10 inch Solid Rubber Tires Tubeless Front or Rear Replacement 10x2.125 Solid Electric Scooter Tire for Gotrax G4 Xr V2 Ninebot F25 F65 Hiboy S2 Pro 2pc Black

Great tire, rides a little harder than pneumatic but is well worth the worry free feeling. I had 2 flats in the past few days, no longer. I checked a few videos and recommended ways to install them due to the difficulty on solid rubber to mount on wheels. I came to the conclusion that by cooking the tire in the microwave wrapped in a wet towel for 4 minutes on each side, 8 min total the tire became soft and elastic enough to mount on the wheel easily. It took me less than 2 minutes to mount in the wheel using a large screw driver and the tool provided by the tire seller. Great tire for a great price!

Muy bueno

They are a bugger to get on but not impossible. It was a bigger chore removing the front tire motor. We got the tire on the rim pretty quick by boiling and muscling it on with two guys. Extra set of hands helps for sure. Be aware the tires are directional. Not a big deal if backwards but be advised all the same.

A little bit harder to install but you need to be with someone. But it fits perfectly on my navee v40 pro.

These tires were insanely difficult to install. I am a large, mechanically inclined guy with plenty of tools and rarely (never) gets stymied or frustrated with something as simple as this should have been..The only real instructions it came with said to search uTube for “Ninebot scooter solid tubeless tire replacement”, which did not link to the (or any) manufactures video but just random nice people out there who have created and posted their own videosSo basically there was no thought or effort at all given to providing their own instructions and they just leverage other people‘s work which is a cheap and unethical tactic as best.I searched through several videos before finding one that was specifically for the Segway Ninebot and was actually helpful. Even in the videos where the poster had obviously replaced these tires before it did not look easy, most used atleast 2 people, always big guys, no dainty ones who still fought and grunted to get the new tire in place.I followed the instructions I found on uTube to a T and still made no progress (except a lot of cursing) for nearly an hour trying to get this mounted. I boiled it as instructed and still it would not fit. I boiled it and then used my heat gun and still could not mount it. I finally recruited three other family members to assist and we finally got it mounted but the outside of the rim was significantly dented and scratched all over, all the nice looking orange paint strip was nearly destroyed so it looks pretty beat up now. This was only the back tire, given the difficulty and damage to to the back tire and rim I don’t think I will even consider replacing the front tire where the motor is in the hub of the tire.Finally, despite the width measurement of 2.125 specified by Segway and this product says the size is 10x2.25 there is about a 1/8” gap between the tire sidewall and the rim bead and does not engage at all with the bead. This gives the tire enough play when turning it feels like a Normal tire thats low on air. I actually worry a bit that in a sharp turn it might allow the tier to dismount or ”peel” itself off the rim on its own which is almost unbelievable considering the difficulty of mounting it..I know the benefit of not worrying about flat tires is enticing but I am not sure it is worth the frustration and cosmetic damage to the rim that results from the install.YMMV - Litterally ;-)

Just like many other reviewers the tire was difficult to install on the wheel:1. Heated in the microwave about 3 mins.2. Soap on the tire/rim a must3. After removing the wheel and disassembling I stood on the wheel (part w/o motor) and used a screw driver to pry the tire on to the rim. At some point it popped. This part was hard.4. Had to use clamps (see photos) to get the tire on the other side of the wheel and screw the wheel back together. Lining up the screw holes was actually easier than I thought it would be. Recommend taking off the brake disc during this step. I ended up bending mine slightly. This step was very difficult.5. Putting the cable back on was the most challenging step. I didn’t have pliers which would have been helpful. Matching up the arrows and getting enough leverage to get the cable back together was … frustratingI would say I’m average when it comes to being a “home engineer “ or handyman… this install was really difficult.

Fitted this to my sons Hiboy S2 pro. It is important to make sure the internal width of the tyre fits your wheel. We spent 2 hours trying to fit another tyre which was too big.The tyre came with a tyre spoon/iron.We boiled the tyre in water for 15 minutes, used dish soap around the wheel and while hot fitted using tire irons/spoons from Dr Roc. 3 hands helps a great deal.Overall 20 minutes to fit including boiling time. Fast delivery high quality, no complaints.This will not be easy if you don’t have tyre irons/spoons and don’t boil the tyre before install.

The media could not be loaded. the tires are great. the install was rough. after 30min of bending over and my back just HURTING the right way to install the hit me. i posted a short video to help. basically boil the tires for an hour or so. next use the provided tool to get the tire on the rim. now the big thought. take a big pair of slip-joint pliers and squeeze the wiggle the tire into place. i felt a little snap. rotate the tire and repeat. dont kid yourself like i did and think "im in construction im strooooong". its a wrestle