Bevel Engineering Extended Fender Flares Mud Flaps Guards for RZR XP 1000 Polaris RZR XP 4 1000 Full Set Front/Rear

Here is a completely unbiased and non-sponsered review.The goods:Front fender fitment is greatPlenty of extra hardware for installationThey do the job well for on offset rim and wider tire.I'd say 75% of mud is kept out of the cab vs. having no flare on there. The rear cargo area also stays a tad cleaner.My intake screens seem to stay a lot cleaner. Most of you big mudders will appreciate that.The bads:These things are WIDE. I would not recommend them for a stock wheel/tire combo unless you want to trim them yourself. It will just look goofy.... That being said, they fit my application well.Rear fender install is easy, however, the body line bothers me.After a few hot days(70 degrees in Alaska, yeah that's hot to us) the rear fenders started to droop down. This adds to the weird body line.The instructions only say to add two stitch screws to hold the rear fender in place on the upper stock flare. Not a chance in hell that will hold. Luckily they added extra hardware so I drilled 1/4 inch holes and used the provided Allen screws and washers to secure it.All in all, I'd recommend them for a bigger wheel and tire combo. They do very well at keeping stuff from splashing in your face or throwing mud on your neck only to have it run down to your ass crack. If the body lines were tighter they'd be a 5 star from me.

The bad first: there were three screws missing on one of the rear flaps, but I was able to subsititute them rather easily.The good: These worked like magic! Prior to installing them, me and the interior of the RZR would be covered in mud, dirt, and grim whenever I rode in wet conditions. I put these flaps to a hellacious test the day after heavy rain. I rode some trails in the desert near Florence, AZ. I rode fast, slow, and hit puddles going 50+mph, and no mud got on me. These things work. The quality is very good. The installation took about an hour or so. There was nothing too complicated about it. I drilled pre-holes to make it easier to place the screws. Hands down, this was a great purchase. I thought the RZR would look silly with the extra wide flaps but it really doesn't I attached some photos to help.

Flaps fit my 2019 xp 1000 ride command pretty good-front flaps fit pretty good and rear same but I had to add my own top securement (they come with two very small screws and I did not like that). The bends in the fenders came pretty close to fitting OEM fenders but not perfect. Thats just me and being picky when it comes to proper alignment. Other than that they do keep the mud out of the cab and look good 4 stars because of the small rear fender screws and alignment

Front fender flare extenders fit like a glove. Easy to lineup with existing mounts and secured using 11 self tapping screws. The extenders are not very bendable but set inside the after market MSA32 15” wheels with 4x3 offset. Rear extenders did not fit as well. The curvature did not fit the rear body lines as nice and stuck out past my wheels. I ended up trimming them down 1.5” in width and angling the rear to match my rear fender flares.

Awesome they look great and REALLY EASY TO INSTALL, and appears to be able to block the mud, and illuminates the need for a back glass. will update after first mud ride.

Installed on a 2016 rzr 1000xp. Went on one ride which wasn’t even that muddy one mud flap fell off of my fender and the other one cracked and broke. See picture. They are not that sturdy or strong. Would not recommend. Wish I could get my money back or a new set at least. Update finally got a hold of the manufacturer direct. Super friendly and helpful sending me a replacement mud flap at no charge . Maybe I just had a defective one from the start.

Modified therear set, made them a bit smaller. Found they cause snow to fly into drivers cab area. Cause it was so light and fluffy. Mud wasn't an issue, onkysnow. But,since we ride in the snow alit,we narrowed them just a bit.

Did not like the way the rear fenders look or have to be mounted I had to do a some trimming and ended up taking them off completely from the rear love the front ones