🚗 Unlock the Future of Convenience!
This Smart Keyless Entry Remote Control is a brand new, fully compatible replacement for Chevy Camaro, Cruze, and Malibu models from 2016 to 2021. It features 5 buttons, operates on 433MHz radio frequency, and includes a lithium battery. With a maximum range of 10 meters, this ergonomic key fob ensures easy access to your vehicle while providing a cost-effective alternative to dealership prices. Enjoy hassle-free programming and 12 months of technical support for a worry-free experience.
| Button Quantity | 5 |
| Controller Type | Button Control |
| Number of Batteries | 1 Lithium Ion batteries required. (included) |
| Supported Battery Types | Lithium |
| Maximum Range | 10 Meters |
| Compatible Devices | Thermostat |
| Connectivity Technology | Radio Frequency |
| Special Features | Ergonomic |
| Maximum Number of Supported Devices | 1 |
J**N
Honest seller
All was good
M**A
Great product
Fit perfectly for my 2020 chevy malibu lt
P**G
Signnal too strong
Car would always signal "key left in vehicle" while it was in my pocket outside the car. Had to move several feet beyond vehicle to lock car.
T**2
Works With Chevrolet Blazer, Too
This replacement keyfob works perfectly with my 2021 Chevy Blazer. The main difference is in the appearance of the icon on the hatch release button - as you can see in my pic, it looks more like a trunk than a liftgate on the replacement keyfob.Here are the steps I used to program the keyfob to my Blazer (NOTE: requires 2 already programmed keyfobs):1. Remove the lock cylinder cap at the rear of the outside driver door handle by inserting a key into slot at bottom of cap and prying up.2. Place 2 already programmed keyfobs into the front cupholder.3. Insert a correctly CUT key into the lock cylinder, and rotate counter-clockwise 5 times within 10 seconds. The driver info. center should display "READY FOR REMOTE #X" where X equals the number of already programmed keyfobs plus one.4. Remove the programmed keyfobs from the front cupholder, and replace them with the new keyfob.5. Press the Engine Start button on the dash. When the keyfob is successfully programmed, the driver info. center will show that it is ready to program the next keyfob. Remove the new keyfob from the cupholder, and press its lock or unlock button (doors should lock or unlock, accordingly).6. IMPORTANT: Press and hold the Engine Start button for 12 seconds to exit programming mode.Please note that this replacement keyfob still needs its mechanical key cut specifically for your vehicle in order to mechanically lock/unlock the driver door (in the event of loss of battery power in the vehicle or keyfob). The mechanical key is attached to the keyring loop, and is accessible by pressing the chrome button on the side of the keyfob.
N**E
Works a little TOO well
I ordered two of these and was able to pair to my Chevy Cruze. One of units had a dead battery but I switched the battery out and it worked no problem.However, when you exit the vehicle with the keys in your pocket, the car still thinks they are inside the vehicle. You need to hold them away from the vehicle for it to tell you exited the vehicle.Still. Better than not having any keys at all :)
K**J
Perfect
I ordered this for my 2020 Chevy Malibu. When I bought it the dealership only gave me one key fob. So I got this one so my husband can have a key fob as well. I went to the instructions that were provided online and found how to program it. I found out later that the program instructions were also in the owner's manual. It took about 30 minutes, and the directions were easy to follow.
R**.
Works great
Works great. All buttons works. Only complaint I have is I keep getting a message saying I left the key in the car even when the key is no where near it
D**S
Time to receive the item was wonderful
Doesn't hold the program
Trustpilot
3 days ago
1 week ago