ThermalrightAXP90 X47 Low Profile CPU Cooler, with 92mm TL-9015 Slim PWM Fan, ITX CPU Cooelr Fan, 47mm Height,for AMD AM4 AM5/Intel 1150/1151/1155/11851/1200/1700(AXP90 X47)

This is a nice cooler...it is in a inwin b1 on a 5700G built around the ASRock b450 itx fatality...my main complaint with noctua similar but more popular offering is the direction it vents, it pushes air out left and right vs up and down so basically airflow is cut off by the memory and IO area ..this one from thermalright is exactly opposite it vents out the top and bottom(with convection mostly top) so this little problem as basically gone, the mounting mechanism defenetly isn't noctuas famously easy to use one but it's effective and considering I'm not going to be taking the cooler off twice a week it's fine and iv defently seen worse on soposedly high end cooling solutions so I have no complaints...if I were to pick a single thing to hone in on with this brand it's the smorgusborg for varients they offer, 36mm copper(black or gray) 43mm aluminum copper or black copper, 53mm in all versions mentioned above, all difrent weights...ya it's a bit much for your average consumer...but that being sead I was able to find 2 that I liked that would not only maximize the height in my specific case wile leaving enough of a gap to pull in air but I also had a choice of color so there is that...but I think to drive my point home here I ended up buying 2 one all black that is soposed to be coated copper and one that is just all copper becase aperently even tho they are the same under the coating they are showing in the description as difrent weight and wattage so we will see about that once I receive the secound all shiny copper heavy one lol...overall I like them they are not over engenered just to make a basic mistake like push the air in a direction that on every itx motherboard made in the last 10years has many large tall things called ram modules RIGHT there basically eliminating any benefits of your product being heavy dense and well built lol...good job thermalright you didn't forget the basics-----------Update I just received the full copper revision of this model and yes it is infact noticeably heavier...I will defently be swapping out the all black one for this one and pairing it with the noctua slim 92mm fan from a nh-l9a and probebly artic MX 4 compound and doing some before and after testings on all the difreces...I'm not realy shur why this model is heavier than the black one as the black one is soposed to be full copper aswell just painted with a thermaly conductive paint and also nickel plated but we are going to find out what the results are of the difrences after testing...I want to be clear I like the all black model and the fans on these are ok, I will not be returning whichever one I don't use for this build long term I just want to make shur I am pairing the best possible solution with this 5700G to get the best possible cooling performance so I don't have to worry about my CPU temps in this airflow anemic case that is the inwin b1...lolI will likely just copy and paist this review for the copper one so there is a bit more feedback for both models becase as of right now there is very little user feedback on these and that a shame as they both have the same benefits over the noctua LP coolers that being they blow air up and are not blocked off by the memory or IO area(cooler or integrated sheald) but all the info in this review is still relevant for the copper one especial this part lol

I wouldn't use this particular CPU cooler unless you needed the low profile form factor. This was the case for my corsair bulldog and the AIO liquid cooler went out. Saw my temps spiking 90+ and needed a replacement but the original cooler wasn't available anymore and also didn't make sense if it failed once to get another one. So I got this, which worked perfectly to keep my temps normal again. It comes with thermalpaste so you don't need to buy anything else. Its low profile fit into my case just fine, whereas regular CPU cooler would stick up too high. Very quiet too, and I went into BIOS to adjust its speeds no problem.

Thermalright AXP-90 X47 Full Copper CPU heatpipe type heatsink on an ASROCK DeskMeet B660:It just fit. It is quiet. The power supply fan has a louder whirr. At about 6 ft the combined noise added to ambient (55db) was only about 1db as measured by an instrument (not a phone) and most was from the PS fan. The DeskMeet 500W power supply fits over it with air flow from the outside, through the power supply and to the heatsink fan. A motherboard power cable seemed to need to go on top or close to one side of the heatsink and just had room for the wires. I didn't try orientation or even looking at the heatsink geometry to see if orientation matters. The two fan headers just had enough room to plug in a case fan and CPU fan. Other motherboards will have a different arrangement, of course.Used an i9-13900 65W CPU. Being for audio the CPU load is minimal. Wanted to see if more cores improve sound quality over an 8 core 16 thread PC with the same Win11 Pro OS - still evaluating. Sounds great regardless. Turned Turbo Boost off which took the edge off making it sound more relaxed (base speed 2GHz). Even with Turbo Boost enabled and as an audio player no real heat is produced so this unit keeps up fine. So, for more severe applications this review won't help with regard to CPU temperature but the heatsink has to be less than 54mm and this is around 32 to fit in a DeskMeet B660. Good low-profile heatsink.

The media could not be loaded. The unit I got had a broken bracket where 1 out of 4 screws wouldn't stay screwed in (see video). That means when I installed it, I was only able to tighten it 3 out of 4 sides.Im getting a replacement because it performed well even thought it was like that. I used it with a ryzen 3600 and it cooled it very well (around 54deg) even with its defect.It was easy, but confusing at first to install and the fit was really nice. It gives so much clearance for air to pass through. It is even better than the stock wraith stealth cooler. The fans were not going full speed and it was quiet unless under full load.Overall, its a great product but I am removing 1 star because it came with a problematic bracket. They need better QC.

I run a small PC repair and custom build company on the side and occasionally source parts from Amazon.Out of the 20 or so Thermalright products I've ordered this year, this is the second time I've received one with zero packaging/foam to protect the cooler and it having been clearly used before. See pic. Thermal paste all over the heatsink, and the cold plate is all scratched up as well.What's more is I now have to disappoint a customer who has to wait another couple of days for a replacement, which hopefully hasn't also been used.Unacceptable, especially now knowing this is not a one-off.I love these great value and high performing coolers, but I am not okay with this kind of quality control.Thermalright, do better.