Zooz Z-Wave Long Range Q Sensor ZSE11 800LR | Motion, Temperature, Humidity, Light (Hub Required)

UpdateThis is the 2nd generation of this device. I was hoping they fixed the battery issue. Batteries last less than 30 days. This is reason it has two batteries, and a USB port for power.Below the s original review below.Worked right out of the box. You do need to download the driver. Instruction were clear on how to load the driver. It was point and click on the Samsung site.After loading the driver, SmartThing correctly displayed the motion sensor and you could access all the parameters.

I first powered three of these with batteries. I was able to bind them with my Home Assistant with no problem. One is still working. One is powered, online, and doesn't detect motion. The third only works with applied power.However, the one that works with applied power works very well. So I'm rewiring my shop to provide USB power to these devices.I wouldn't recommend because of this unreliability. Or, use direct power.

This sensor is a great choice for HomeAssistant and Hubitat users.Just grab the Zooz driver from their website and you're off to the races.I use it in a garage to control the lights and it has been very configurable, quick and reliable.I dropped this thing like 12ft onto concrete when installing (Don't recommend), but the sensor was completely fine. The mounting options are great (screws or adhesive pad) and the fact that it can be USB powered is perfect for permanent/hard-to-reach installations like a ceiling.Don't be deterred by reviews from inexperienced users, if you've used Zooz products in the past, you know the quality and support you are getting, and this sensor is no exception.

I have this device installed under an eve primarily for motion detection.The motion detection works well.The temperature reading was stuck permanently at 72.5 degrees F. The actual temperature was closer to 50 degrees. The reading did not change over a 12 hour period. I verified that SmartThings was using the correct Zooz Edge driver.I removed and re joined the sensor. Now it reads 68.4 degrees and doesn't change.I don't need the temperature, but it would be nice.Due to the difficulty of removing the sensor, I plan to keep it despite its shortcomings.Based on other reviews of this product, it appears that Zooz has a quality control issue.Buy at your own risk.Update:Both started updating temperature after more than a day. One is USB powered and reads close enough to the actual temperature, about 2 degrees low. The other is battery powered and reads about 10 degrees lower than the actual temperature.Speaking of batteries, the battery powered device runs through a pair of CR123 lithium batteries about once per month. Through the SmartThings app I have disabled everything but motion detection, yet it still runs through batteries at an alarming rate. I need to find a way to get it USB power or use it somewhere else where I have better access to power.I have an old Zooz 4-in-1 sensor that has been working perfectly for several years.I'm really disappointed in these ZSE11 devices.I am deducting an additional star, down to one, these are junk.

I have two of these sensors and was hopeful they would meet my objectives. Unfortunately, the majority of the measurements suffer from poor accuracy and limited resolution.Motion:Motion detection is the most reliable of the ZSE11 features and works quickly and with good range and vertical and horizontal field of view. With ST device type handlers installed, there are options to raise/lower sensitivity as well as enable/disable an LED indicator light when motion is detected. I rate the motion detection solid 5/5. It's as good or better than several other z-wave motion detectors I have.Temperature:Out of the box, my sensors' temperature readings were consistently 3-4 degrees above actual air temperature. This in itself is minor and correctable by applying temperature offsets in the settings. But another limitation is that the frequency of the measurements is limited to 1 hour intervals or temperature changes of at least 1 full degree. Consequently, the data collection will not reflect temperature readings with high resolution. This is surprising given that temps are reported with precision to 1 decimal point. If actual temperature fluctuates +/- several fractions of a degree several times within a 1 hour period but never exceeds a net 1 degree change, then the ZSE11 will record NO change in temperature during the 1 hour period. Every other z-wave device I've owned for years is able to gather temperature changes at a much finer frequency/resolution. So it's shocking that the ZSE11 is so limited. Rated 3/5.Humidity:The out of box humidity readings for my two sensors were a stunning 15% above actual humidity. This was observed in a variety of settings within my home from the basement to the second story floor. The ZSE11 would even report humidity readings that were *higher than the outdoor ambient humidity* (during Summer which should be impossible) all while my home was being continuously air conditioned. Likewise, in a closed room with a 500W dehumidifier running, the ZSE11 would report higher humidity levels than other sensors reported in adjacent non-dehumidified rooms. To its credit, the sensor would detect actual changes in humidity seemingly fine, but it's just very disappointing that the accuracy of the measurements was so incorrect. No factory-new measurement instrument should ever be 15% off calibration. Also, as with the temperature readings, humidity measurements are only reported at 1 hour intervals or for changes of at least a full 1%. So again, humidity is measured to 1 decimal place, but the granularity of the readings is very limited. As with temperature, I find the ZSE11 to perform below average in measuring and reporting humidity as compared to other z-wave products. Rated 3/5.Illuminance:Of all the functions I wanted the ZSE11 to perform, this was the most anticipated but sadly most disappointing. The range of light detection is apparently from 0 to 100,000 lux. The light reporting threshold can be set from as low as 1 lux to as high as 30,000 lux. And the light measurement can be offset anywhere between -20,000 lux and +20,000 lux. I want to draw attention to the scale reaching into the tens of thousands of lux. Because I can't understand what type of use case or environment would involve such absurd levels. In case it's not obvious, I'm deeply frustrated by the poor performance of the light sensing capability of the ZSE11. It seems to be designed to monitor stadium lights, nuclear explosions, or solar output, things that would possibly involve thousands upon thousands of lux. HOWEVER , THIS SENSOR IS NOT ABLE TO DETECT SMALL LEVELS OF LIGHTING. More specifically, it cannot detect when a completely dark room transitions to a dimly lit room when natural sunlight arrives during the day. In fact, it consistently under-reports light levels even with normal artificial lighting fully turned on. Rooms with light levels well above 100 lux according to light sensors on various phones and cameras all produce lux levels below half their actual values when measured with the ZSE11. Most significantly, any low light levels which would normally register at or below ~40 lux are reported as 0 by the ZSE11s. This renders the light sensors nearly useless for any kind of illuminance-based automation (i.e. "activate lights only if room is too dark"). A little research will show that it's not unusual for homes to have areas with lux levels ranging from 50 lux to 300 lux. So it stands to reason that these sensors should be calibrated to handle light levels in those low ranges, rather than in the tens of thousands of lux. Also, unlike with the temperature and humidity issues, the light level inaccuracy CANNOT BE CORRECTED with an offset setting. This is because the sensor physically cannot differentiate below a certain level. Any offset adjustment will simply result in that value being falsely reported as the new minimum value (e.g. an offset of 50 lux will cause pitch black rooms to appear as being lit to 50 lux). I had such high hopes for the light sensing capability of the ZSE11, but I cannot imagine there are any worse performing z-wave light sensors available. Rated 1/5.Other:Despite the above criticism, the ZSE11 does offer some redeeming qualities. The support for micro-USB power is especially welcome as it eliminates the chore and annoyance of replacing sensor batteries. For me, this on its own justifies keeping the sensors as replacements for battery-powered motion sensors. Additionally, the ZSE11 will act as a z-wave repeater when configured with USB power. Setup went very smoothly for me although I have extensive experience with z-wave and ST device type handlers, so other users may form a different opinion.

Work great, a little sensitive, but can work around. Use with Hubitat hub.

I had previously purchased a Zooz ZSE40 4-in-1 sensor, and it has been operating very well for close to 5 years. I required adding 4 additional Zwave motion sensors to my smart home, so decided to get the newer Q Sensor. The sensors all paired with my smart home (HomeSeer) controller very easily, just as the ZSE40 had done. However, once the sensor devices were being monitored, I noticed that the temperature readings that they were providing were significantly off, as well as the humidity readings. I searched for information on how to calibrate them, and found nothing. In addition, which was even more frustrating, was that the motion sensors would simply not detect motion from time to time. I use the sensors to automatically turn on lights when someone enters a space/room, and I expected them to always detect motion. I had the sensitivity set to 8 (maximum), and still they missed an incoming person about 25% of the time. I double checked everything, and even took the time to remove them from my system and re-add them to my Zwave network. I probably spent 6-7 hours messing about with these sensors, and after reaching out to Zooz customer support (which was very close to useless), have decided to return the four sensors to Amazon, and will look at similar sensors from other vendors.Although, I don't know the subtle differences between the Q sensors and my ZSe40 4-in-1 sensor, I do know that the sensitivity and reading accuracy has suffered significantly. I would have expected them to work better, as they are newer and able to leverage better technology, but this was not the case. It may been more that Zooz decided to use inferior (less expensive) components in order to increase their profit margin on these devices.

This sensor is pretty good for the price. I just purchased another. I wish it would do air pressure too. Shipping was slow, but it was over the Christmas period of 2021.