HUANUO 13” - 32” Single Monitor Arm for LED LCD Screens, Height Adjustable 360 ° Rotatable Gas Spring Arm, VESA 75/100 mm, 2 Mounting Options, Weight Capacity 1-8 KG (White)

Let me preface this review by saying this is the first monitor stand of its type I’ve used or owned, so I have nothing to compare it to. I have only used the basic stands that are supplied with monitors from the factory.I think I was lucky when I bought this as it was £19.99, it has gone up to £29.99 in the week since I bought it. However, even at £30, I think this is good value for what I received.The product looks well finished off, well put together and appears to be sturdy (again, I can’t compare to other more expensive stands). If I bump or bang my desk, there is minimal (to no) wobble with my 19” monitor attached. And no more than I had with the regular stand it came with (especially considering that it was standing on a small box to raise it up…).It arrived in a well-packaged box in, basically, 5 parts with a bag of sectioned off screws and bits, which was well labelled, and an instruction booklet that was clear and easy to follow.Most of the main bits were already assembled. I had to attach the clamp with pole, two parts of the arm, the monitor bracket and cable tidy, and that was it (at least for me).The bracket that attaches to the back of the monitor has holes for two different hole offsets. There is a selection of 16 screws, two lots to allow for different thread thicknesses. Each of those then has two different lengths to allow for flat and curved monitors (and a set of 4 spacers). ). You can easily unclip the monitor from the stand if you need to.It comes with3 different sized Allen keys (or hex wrenches if you prefer). These are for making changes (if you have a desk thicker than 60mm, for example), tightening if needed over time and adjusting the arm tension as required. The supplied clip goes on the pole where these can be stored; this clip also acts as one of the cable tidies.There is a second cable tidy that runs underneath one of the arms and is held in place by three screws. I’d suggest you will find it easier to fit this before assembling anything else.As the stand was adjusted out of the box, my monitor (a lowly little and relatively light 19 incher) is on the edge of adjustment for tension. It requires some force to move down but very little to raise. If I were to move it around often or have anything even a bit lighter, I would adjust it. It is supposed to handle monitors from 13” to 32”, so I expect anything closer to the end of the ranges will need to be adjusted. Still, I would expect this, and it appears to be easy enough to do.I’ve only had this stand a short time, so only time will tell as to how well it will last.

I wanted a white and silver monitor arm which are far and few between, I wanted height and distance adjustment too, so this item fits the bill.I wouldn't say that putting it together is difficult, the instructions aren't great though, but it's not hard to figure it out. Expect spare parts because if you're not attaching to a very chonky desktop, some of the bits are refundant.I think my single complaint is that you have to tighten some parts very hard to keep them in place at all, which in turn makes adjustment difficult.My monitor isn't heavy at all but I had to put some serious effort into tightening up the screw dedicated to vertical tilt, in turn if I do want to tilt the monitor, I have to put more force onto the bezels of the monitor than I'd like to. To be fair, I'd say it's the only axis that presents a problem, changing height is great due to the gas assisted chamber, but a height adjust will always require a tilt adjust too.Cable management is sufficient, it would have been nice if the entirety of the cable could be hidden inside, but perhaps this would have compromised the strength of the arm.It's built like a tank so I have no worries at all that this will hold my monitor up perfectly for a very long time.

My current monitor mounts are ok but after seeing this on sale I couldn't resist giving it a try, i've been using monitor desk mounts for many years but I have never had a gas / height adjustable mount. The quick release clips are a real benefit for installing without an extra person to help, and make it much easier to manage when you need to get things out the way to do some work around the desk. The height adjust is also great if you have a deep desk and end up putting a bunch of things behind the screen, much easier to get at everything. The easy height adjust also gives the option to use the screen in a vertical alignment with minimal fuss, something that was not easily achievable with my non gas mounts.My only question with the mount is its weight limit, I currently have an old 24" on it and it is working great, hopefully when I upgrade to something larger it will continue to work as well, it would be nice if it had a slightly higher upper weight limit but for the price can't really complain.

Not often I leave product reviews, but I feel obliged to on this case due to being really pleased with the product.Most of my friends and colleagues have a monitor arm or two but I have always put it off as I did not see the point. Having purchased this one I am really happy. Not only do I now see the benefits, this particular arm looks really nice, sleek and was easy to assemble. I currently have it clamped to my desk but looking to cut a whole for grommet mounting.I have already recommended this product to my circle of contacts and a number of people have purchased it despite having had owned one already. Would not hesitate to recommend, if I needed another I would not look elsewhere. A friend ordered his in all black, but this one looks much better in my personal opinion.

There's so many similar ones on here, I just went with the cheapest in the end. Have to say, pretty happy with the outcome. Just clamped it to my (standard office style) desk. the clamp covers the metal frame and the desktop, as there's not enough overlap to just use the desktop. Been moving it around all over, as I use the monitor for work or watching the footy from the sofa. Not moved at all clamp-wise, and done exactly what I need. It does need free space behind it though, I have a window ledge it juts over, when I push it back. If you have a blank wall, I'd look at a straight arm style one maybe instead. Depends what range of motion you require, but definitely something to bear in mind. It's painted white, with a silver/chrome pole and black plastic parts, not that easy to tell in the photos. At under £25 though? Bargain.

J'ai acquis ce bras de support pour écran pendant les prime days a 21.29 € et le produit vaut très largement ce prix.**PACKAGING**Le produit arrive dans une boite cartonnée, avec le logo de la marque sur le côté.Le bras démonté est rangé dans un "moule" en carton avec chaque pièce dans un compartiment, le colis est lourd.Il y a chaque pièce démontée * : (le bras en lui-même est en trois pièces : La barre qui se fixe au bureau et qui va supporter le bras, La première partie du bras qui bouge uniquement en rotation circulaire, la deuxième partie du bras qui contient le système de ressort a gaz et qui permet d'effectuer la plupart des mouvements)- Le bras*- Le support VESA (qui contient le 75 mm et le 100 mm donc une adaptation à la plupart des moniteurs récents) qui se fixe au moniteur- La visserie (qui contient aussi les clés allen qui permettent de changer la pression ou simplement de visser certaines vis, attention un tournevis cruciforme sert aussi dans le montage)- La notice- Support de rangement pour câblesLe packaging est très simple, pas de message de bienvenue dans la boite ou de boite coloré avec une image du bras ou un gros logo.**MONTAGE**Lorsque l'on déballe le paquet, on se retrouve avec beaucoup de pièce. En lisant la notice, chaque pièce est associée à une lettre allant de A à S ce qui permet de nous retrouver dans le montage guidé.Le montage du bras est guidé et expliqué, étape par étape, en montrant chaque pièce à utiliser via leur lettre respective ce qui rend le montage très intuitif et clair.Le + c'est que l'attribution de la lettre va jusqu'aux visseries et aux clés allen, autant dire que cela rend le risque de tromperie très faible.La fixation au bureau a une grande marge dans le cas ou l'on garde par pression, mais peut être fixé aussi via un trou dans le bureau, ce qui permet de s'adapter à la grande majorité des bureaux (voire tous).**ERGONOMIE**Lorsqu'il est monté, le bras permet de bouger le moniteur dans grand espace, grâce à son ressort à gaz et son montage en deux parties qui permet de le monter dans un espace restreint en le "pliant" de la bonne manière.Ce qui change des bras à ressort à gaz traditionnels, c'est le fait que le bras est posé sur une barre, ce qui permet d'adapter la hauteur à notre guise même en position debout.La tension du bras est réglable en serrant/desserrant une vis via les clés allen fourni ce qui permet de s'adapter à n'importe quel moniteur, peu importe son poids (en restant dans les limite prescrite par le constructeur)Le bras permet de manipuler l'écran en le mettant dans n'importe quel positon que ce soit en position portait ou paysage, ou même en le disposant de sorte qu'il soit orienté vers nous de manière optimale.Le bras contient nativement un support de rangement pour câbles, et ils en fournissent un autre à fixer de manière à faire une installation propre. Il y a la place pour mettre environ 3 câbles bien épais en laissant du jeu.Il y a aussi une petite fixation sur la barre à mettre afin de faire passer les câbles (et de les réunir) et de ranger les clés allen de manière à y avoir accès très rapidement.Ce qui permet de maintenir le bras en hauteur sur la barre est une cale qui se visse et qui se dévisse via un système similaire au système du cliquet, ce qui rend pratique et intuitif le changement de hauteur du bras, toujours + d'optimisation.Le seul point négatif, c'est le fait que certaines manières de pivoter le bras sont assez dur et ne se règle pas, ou du moins j'ai eu le problème de la vis qui ne se règle pas, mais de bas, c'est tout de même très maniable et ne nécessite pas une force sur humaine.Pour résumer le bras a un rapport qualité prix (sur les prix du prime day qui s'apparente à être le prix normal après quelques jours d'attente) très bon, le bras est robuste, a un beau design et ne fait pas tache sur le bureau et l'intuitivité du montage est très importante et ici elle à bien été travaillé (à mon gout).Pour le prix conseillé (59.99 €) je pense que le prix est légèrement excessif, mais nous connaissons Amazon sur le choix des prix conseillés ;).si mon avis vous à plus, n'hésitez pas à mettre un vote utile ;)

The versatility that this product provides, is out of this world. I had a decent monitor with a good monitor stand, it was one of the reasons why I even opted for that specific monitor. But the arm does a couple things that a monitor arm cant:1. It clears your desk by 90%.My desk has felt cleaner for the last 7 days than it has for the last year. Dust doesn't collect in tiny corners of your monitor stand anymore.2. It offers you viewing angles that you hadn't thought of before.I can relax and lay back on my chair, or turn my monitor to the left and watch from a decent angle from the comfort of my bed. I have had one other monitor arm for my secondary monitor but I've returned it for another one of these, as it is just a lot easier to tune, and adjust in terms of height, and swivel.I have two of these and might get a third in case I buy a third monitor :)

Ho acquistato questo braccio in sostituzione di un altro (di marca differente) che non aveva tutte le caratteristiche necessarie per posizionare il mio monitor da 28" sulla mia scrivania.A differenza del precedente, questo ha una base di aggancio molto robusta e solida, bracci lunghi e robusti, la possibilità di posizionamento molto più in alto grazie al tubo verticale.Ho una scrivania piuttosto larga (80 cm) e mi occorre un braccio lungo. Il precedente, e la quasi totalità di tutti gli altri disponibili, non raggiunge i 60 cm. Questo arriva fino a 61 cm e forse è l'unico. La lunghezza mi permette di avere il monitor alla giusta distanza dagli occhi.Volevo posizionare il monitor al di sopra del mio PC portatile e mi serviva un braccio di sostegno che permettesse un livello dal piano adeguato, complicato perché purtroppo il monitor ha l'attacco VESA nella parte superiore e non al centro. Mi serviva un braccio molto alto. E questo è della misura giusta (un paio di cm in più sarebbero stati anche meglio, ma non ne ho trovato nessuno che ci arrivasse).Infine il morsetto di fissaggio è davvero solido e una volta serrato non si muove.Tutto davvero molto robusto e stabile.Il montaggio è stato immediato, senza alcuna problematica.Unico neo: avrei preferito un modello completamente nero, ma solo quello bianco ha le dimensioni giuste. E' un aspetto secondario di natura puramente estetica.Pienamente soddisfatto. Adesso ho la scrivania sgombra e il monitor dove mi serve, con la possibilità di spostarlo facilmente in caso di necessità.

Il prodotto di per se non è male, anzi. Per il prezzo pagato, 19 euro circa, li vale tutti! Ci sono però varie cose che mi hanno dato fastidio. Innanzitutto le istruzioni non sono molto chiare, infatti, la traduzione in italiano non è il massimo dati i vari errori grammaticali, e le istruzioni sul montaggio in generale non si capiscono molto bene. Un'altra cosa che non mi è piaciuta, è che quando, per motivi di spazio, si piega il braccio, il monitor appare leggermente storto a causa del peso non distribuito bene. Nel complesso, per chi ha la scrivania giusta e, soprattutto, lo spazio necessario, è un ottimo prodotto. Il materiale non è male, anzi, è un buon materiale. La chicca di questo braccio per monitor, è la possibilità di montarlo in 2 modi, sfruttando addirittura il buco della scrivania predisposto per il passaggio dei vari cavi. E' stato anche ben imballato, cosa non scontata. Un'altra cosa utile è il set di brugole fatte su misura per stringere e allentare le varie viti per il montaggio o per la regolazione del braccio. Inoltre si può montare anche su monitor curvi. La cosa che, purtroppo, mi ha portato alla restituzione dell'articolo, è il tanto spazio che occupa. Comunque, per chi non vuole spendere troppo, consigliato.

Zweck: Fernsehbildschirm als Zweitbildschirm flexibel an Schreibtisch anbringenEntscheidung für Produkt: Stabilität, Flexibilität und Eignung für große BildschrimeMaße Fernseher: Bildschirmdiagonale 80cm (32 Zoll), Gewicht: ca 6 kgMontage des Produkts: sehr einfach, zwei Möglichkeiten: einmal zum Anklemmen an den Schreibtisch zweite Variante Montage auf einer Bohrung in der Tischplatte. Anleitung war gut und die Teile waren gut beschriftet.Die Einstellungen für den Halter sind etwas kniffelig, aber wenn man mit Ruhe und Sorgfalt vorgeht kein Problem. Die Teile und Schrauben sind kein Mist. Sie sind stabil und werden auch nicht gleich rund.Der Halter ist stabil, ich kann den Fernseher in alle Richtungen drehen, neigen und schwenken und er behält die Position. Ich habe ihn etwas höher über meinem Laptop montiert als Zweitbildschirm, funktioniert einwandfrei.Einzige kleine Nachteile: Der Schwenkarm direkt am Rohr sollte zum Drehen bei so schweren Bildschirmen etwas angehoben werden, der Preis ist saftigAnsonsten bin ich sehr zufrieden, die Investition hat sich gelohnt. Für meinen Zweck perfekt.Die Bemerkungen über ein Abklappen des Bildschirms kann ich bei meinem Produkt nicht bestätigen. Auch lassen sich die Justierschrauben einwandfrei anziehen und halten die Position.Ich würde mich wieder für das Produkt entscheiden.